1 | /****************************************************************************** |
2 | * |
3 | * Name: actbl.h - Basic ACPI Table Definitions |
4 | * |
5 | *****************************************************************************/ |
6 | |
7 | /* |
8 | * Copyright (C) 2000 - 2019, Intel Corp. |
9 | * All rights reserved. |
10 | * |
11 | * Redistribution and use in source and binary forms, with or without |
12 | * modification, are permitted provided that the following conditions |
13 | * are met: |
14 | * 1. Redistributions of source code must retain the above copyright |
15 | * notice, this list of conditions, and the following disclaimer, |
16 | * without modification. |
17 | * 2. Redistributions in binary form must reproduce at minimum a disclaimer |
18 | * substantially similar to the "NO WARRANTY" disclaimer below |
19 | * ("Disclaimer") and any redistribution must be conditioned upon |
20 | * including a substantially similar Disclaimer requirement for further |
21 | * binary redistribution. |
22 | * 3. Neither the names of the above-listed copyright holders nor the names |
23 | * of any contributors may be used to endorse or promote products derived |
24 | * from this software without specific prior written permission. |
25 | * |
26 | * Alternatively, this software may be distributed under the terms of the |
27 | * GNU General Public License ("GPL") version 2 as published by the Free |
28 | * Software Foundation. |
29 | * |
30 | * NO WARRANTY |
31 | * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
32 | * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
33 | * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR |
34 | * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
35 | * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
36 | * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS |
37 | * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) |
38 | * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, |
39 | * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING |
40 | * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
41 | * POSSIBILITY OF SUCH DAMAGES. |
42 | */ |
43 | |
44 | #ifndef __ACTBL_H__ |
45 | #define __ACTBL_H__ |
46 | |
47 | |
48 | /******************************************************************************* |
49 | * |
50 | * Fundamental ACPI tables |
51 | * |
52 | * This file contains definitions for the ACPI tables that are directly consumed |
53 | * by ACPICA. All other tables are consumed by the OS-dependent ACPI-related |
54 | * device drivers and other OS support code. |
55 | * |
56 | * The RSDP and FACS do not use the common ACPI table header. All other ACPI |
57 | * tables use the header. |
58 | * |
59 | ******************************************************************************/ |
60 | |
61 | |
62 | /* |
63 | * Values for description table header signatures for tables defined in this |
64 | * file. Useful because they make it more difficult to inadvertently type in |
65 | * the wrong signature. |
66 | */ |
67 | #define ACPI_SIG_DSDT "DSDT" /* Differentiated System Description Table */ |
68 | #define ACPI_SIG_FADT "FACP" /* Fixed ACPI Description Table */ |
69 | #define ACPI_SIG_FACS "FACS" /* Firmware ACPI Control Structure */ |
70 | #define ACPI_SIG_OSDT "OSDT" /* Override System Description Table */ |
71 | #define ACPI_SIG_PSDT "PSDT" /* Persistent System Description Table */ |
72 | #define ACPI_SIG_RSDP "RSD PTR " /* Root System Description Pointer */ |
73 | #define ACPI_SIG_RSDT "RSDT" /* Root System Description Table */ |
74 | #define ACPI_SIG_XSDT "XSDT" /* Extended System Description Table */ |
75 | #define ACPI_SIG_SSDT "SSDT" /* Secondary System Description Table */ |
76 | #define ACPI_RSDP_NAME "RSDP" /* Short name for RSDP, not signature */ |
77 | #define ACPI_OEM_NAME "OEM" /* Short name for OEM, not signature */ |
78 | |
79 | |
80 | /* |
81 | * All tables and structures must be byte-packed to match the ACPI |
82 | * specification, since the tables are provided by the system BIOS |
83 | */ |
84 | #pragma pack(1) |
85 | |
86 | /* |
87 | * Note: C bitfields are not used for this reason: |
88 | * |
89 | * "Bitfields are great and easy to read, but unfortunately the C language |
90 | * does not specify the layout of bitfields in memory, which means they are |
91 | * essentially useless for dealing with packed data in on-disk formats or |
92 | * binary wire protocols." (Or ACPI tables and buffers.) "If you ask me, |
93 | * this decision was a design error in C. Ritchie could have picked an order |
94 | * and stuck with it." Norman Ramsey. |
95 | * See http://stackoverflow.com/a/1053662/41661 |
96 | */ |
97 | |
98 | |
99 | /******************************************************************************* |
100 | * |
101 | * Master ACPI Table Header. This common header is used by all ACPI tables |
102 | * except the RSDP and FACS. |
103 | * |
104 | ******************************************************************************/ |
105 | |
106 | typedef struct |
107 | { |
108 | char [ACPI_NAMESEG_SIZE]; /* ASCII table signature */ |
109 | UINT32 ; /* Length of table in bytes, including this header */ |
110 | UINT8 ; /* ACPI Specification minor version number */ |
111 | UINT8 ; /* To make sum of entire table == 0 */ |
112 | char [ACPI_OEM_ID_SIZE]; /* ASCII OEM identification */ |
113 | char [ACPI_OEM_TABLE_ID_SIZE]; /* ASCII OEM table identification */ |
114 | UINT32 ; /* OEM revision number */ |
115 | char [ACPI_NAMESEG_SIZE]; /* ASCII ASL compiler vendor ID */ |
116 | UINT32 ; /* ASL compiler version */ |
117 | |
118 | } ; |
119 | |
120 | |
121 | /******************************************************************************* |
122 | * |
123 | * GAS - Generic Address Structure (ACPI 2.0+) |
124 | * |
125 | * Note: Since this structure is used in the ACPI tables, it is byte aligned. |
126 | * If misaligned access is not supported by the hardware, accesses to the |
127 | * 64-bit Address field must be performed with care. |
128 | * |
129 | ******************************************************************************/ |
130 | |
131 | typedef struct acpi_generic_address |
132 | { |
133 | UINT8 SpaceId; /* Address space where struct or register exists */ |
134 | UINT8 BitWidth; /* Size in bits of given register */ |
135 | UINT8 BitOffset; /* Bit offset within the register */ |
136 | UINT8 AccessWidth; /* Minimum Access size (ACPI 3.0) */ |
137 | UINT64 Address; /* 64-bit address of struct or register */ |
138 | |
139 | } ACPI_GENERIC_ADDRESS; |
140 | |
141 | |
142 | /******************************************************************************* |
143 | * |
144 | * RSDP - Root System Description Pointer (Signature is "RSD PTR ") |
145 | * Version 2 |
146 | * |
147 | ******************************************************************************/ |
148 | |
149 | typedef struct acpi_table_rsdp |
150 | { |
151 | char Signature[8]; /* ACPI signature, contains "RSD PTR " */ |
152 | UINT8 Checksum; /* ACPI 1.0 checksum */ |
153 | char OemId[ACPI_OEM_ID_SIZE]; /* OEM identification */ |
154 | UINT8 Revision; /* Must be (0) for ACPI 1.0 or (2) for ACPI 2.0+ */ |
155 | UINT32 RsdtPhysicalAddress; /* 32-bit physical address of the RSDT */ |
156 | UINT32 Length; /* Table length in bytes, including header (ACPI 2.0+) */ |
157 | UINT64 XsdtPhysicalAddress; /* 64-bit physical address of the XSDT (ACPI 2.0+) */ |
158 | UINT8 ExtendedChecksum; /* Checksum of entire table (ACPI 2.0+) */ |
159 | UINT8 Reserved[3]; /* Reserved, must be zero */ |
160 | |
161 | } ACPI_TABLE_RSDP; |
162 | |
163 | /* Standalone struct for the ACPI 1.0 RSDP */ |
164 | |
165 | typedef struct acpi_rsdp_common |
166 | { |
167 | char Signature[8]; |
168 | UINT8 Checksum; |
169 | char OemId[ACPI_OEM_ID_SIZE]; |
170 | UINT8 Revision; |
171 | UINT32 RsdtPhysicalAddress; |
172 | |
173 | } ACPI_RSDP_COMMON; |
174 | |
175 | /* Standalone struct for the extended part of the RSDP (ACPI 2.0+) */ |
176 | |
177 | typedef struct acpi_rsdp_extension |
178 | { |
179 | UINT32 Length; |
180 | UINT64 XsdtPhysicalAddress; |
181 | UINT8 ExtendedChecksum; |
182 | UINT8 Reserved[3]; |
183 | |
184 | } ACPI_RSDP_EXTENSION; |
185 | |
186 | |
187 | /******************************************************************************* |
188 | * |
189 | * RSDT/XSDT - Root System Description Tables |
190 | * Version 1 (both) |
191 | * |
192 | ******************************************************************************/ |
193 | |
194 | typedef struct acpi_table_rsdt |
195 | { |
196 | ACPI_TABLE_HEADER ; /* Common ACPI table header */ |
197 | UINT32 TableOffsetEntry[1]; /* Array of pointers to ACPI tables */ |
198 | |
199 | } ACPI_TABLE_RSDT; |
200 | |
201 | typedef struct acpi_table_xsdt |
202 | { |
203 | ACPI_TABLE_HEADER ; /* Common ACPI table header */ |
204 | UINT64 TableOffsetEntry[1]; /* Array of pointers to ACPI tables */ |
205 | |
206 | } ACPI_TABLE_XSDT; |
207 | |
208 | #define ACPI_RSDT_ENTRY_SIZE (sizeof (UINT32)) |
209 | #define ACPI_XSDT_ENTRY_SIZE (sizeof (UINT64)) |
210 | |
211 | |
212 | /******************************************************************************* |
213 | * |
214 | * FACS - Firmware ACPI Control Structure (FACS) |
215 | * |
216 | ******************************************************************************/ |
217 | |
218 | typedef struct acpi_table_facs |
219 | { |
220 | char Signature[4]; /* ASCII table signature */ |
221 | UINT32 Length; /* Length of structure, in bytes */ |
222 | UINT32 HardwareSignature; /* Hardware configuration signature */ |
223 | UINT32 FirmwareWakingVector; /* 32-bit physical address of the Firmware Waking Vector */ |
224 | UINT32 GlobalLock; /* Global Lock for shared hardware resources */ |
225 | UINT32 Flags; |
226 | UINT64 XFirmwareWakingVector; /* 64-bit version of the Firmware Waking Vector (ACPI 2.0+) */ |
227 | UINT8 Version; /* Version of this table (ACPI 2.0+) */ |
228 | UINT8 Reserved[3]; /* Reserved, must be zero */ |
229 | UINT32 OspmFlags; /* Flags to be set by OSPM (ACPI 4.0) */ |
230 | UINT8 Reserved1[24]; /* Reserved, must be zero */ |
231 | |
232 | } ACPI_TABLE_FACS; |
233 | |
234 | /* Masks for GlobalLock flag field above */ |
235 | |
236 | #define ACPI_GLOCK_PENDING (1) /* 00: Pending global lock ownership */ |
237 | #define ACPI_GLOCK_OWNED (1<<1) /* 01: Global lock is owned */ |
238 | |
239 | /* Masks for Flags field above */ |
240 | |
241 | #define ACPI_FACS_S4_BIOS_PRESENT (1) /* 00: S4BIOS support is present */ |
242 | #define ACPI_FACS_64BIT_WAKE (1<<1) /* 01: 64-bit wake vector supported (ACPI 4.0) */ |
243 | |
244 | /* Masks for OspmFlags field above */ |
245 | |
246 | #define ACPI_FACS_64BIT_ENVIRONMENT (1) /* 00: 64-bit wake environment is required (ACPI 4.0) */ |
247 | |
248 | |
249 | /******************************************************************************* |
250 | * |
251 | * FADT - Fixed ACPI Description Table (Signature "FACP") |
252 | * Version 6 |
253 | * |
254 | ******************************************************************************/ |
255 | |
256 | /* Fields common to all versions of the FADT */ |
257 | |
258 | typedef struct acpi_table_fadt |
259 | { |
260 | ACPI_TABLE_HEADER ; /* Common ACPI table header */ |
261 | UINT32 Facs; /* 32-bit physical address of FACS */ |
262 | UINT32 Dsdt; /* 32-bit physical address of DSDT */ |
263 | UINT8 Model; /* System Interrupt Model (ACPI 1.0) - not used in ACPI 2.0+ */ |
264 | UINT8 PreferredProfile; /* Conveys preferred power management profile to OSPM. */ |
265 | UINT16 SciInterrupt; /* System vector of SCI interrupt */ |
266 | UINT32 SmiCommand; /* 32-bit Port address of SMI command port */ |
267 | UINT8 AcpiEnable; /* Value to write to SMI_CMD to enable ACPI */ |
268 | UINT8 AcpiDisable; /* Value to write to SMI_CMD to disable ACPI */ |
269 | UINT8 S4BiosRequest; /* Value to write to SMI_CMD to enter S4BIOS state */ |
270 | UINT8 PstateControl; /* Processor performance state control*/ |
271 | UINT32 Pm1aEventBlock; /* 32-bit port address of Power Mgt 1a Event Reg Blk */ |
272 | UINT32 Pm1bEventBlock; /* 32-bit port address of Power Mgt 1b Event Reg Blk */ |
273 | UINT32 Pm1aControlBlock; /* 32-bit port address of Power Mgt 1a Control Reg Blk */ |
274 | UINT32 Pm1bControlBlock; /* 32-bit port address of Power Mgt 1b Control Reg Blk */ |
275 | UINT32 Pm2ControlBlock; /* 32-bit port address of Power Mgt 2 Control Reg Blk */ |
276 | UINT32 PmTimerBlock; /* 32-bit port address of Power Mgt Timer Ctrl Reg Blk */ |
277 | UINT32 Gpe0Block; /* 32-bit port address of General Purpose Event 0 Reg Blk */ |
278 | UINT32 Gpe1Block; /* 32-bit port address of General Purpose Event 1 Reg Blk */ |
279 | UINT8 Pm1EventLength; /* Byte Length of ports at Pm1xEventBlock */ |
280 | UINT8 Pm1ControlLength; /* Byte Length of ports at Pm1xControlBlock */ |
281 | UINT8 Pm2ControlLength; /* Byte Length of ports at Pm2ControlBlock */ |
282 | UINT8 PmTimerLength; /* Byte Length of ports at PmTimerBlock */ |
283 | UINT8 Gpe0BlockLength; /* Byte Length of ports at Gpe0Block */ |
284 | UINT8 Gpe1BlockLength; /* Byte Length of ports at Gpe1Block */ |
285 | UINT8 Gpe1Base; /* Offset in GPE number space where GPE1 events start */ |
286 | UINT8 CstControl; /* Support for the _CST object and C-States change notification */ |
287 | UINT16 C2Latency; /* Worst case HW latency to enter/exit C2 state */ |
288 | UINT16 C3Latency; /* Worst case HW latency to enter/exit C3 state */ |
289 | UINT16 FlushSize; /* Processor memory cache line width, in bytes */ |
290 | UINT16 FlushStride; /* Number of flush strides that need to be read */ |
291 | UINT8 DutyOffset; /* Processor duty cycle index in processor P_CNT reg */ |
292 | UINT8 DutyWidth; /* Processor duty cycle value bit width in P_CNT register */ |
293 | UINT8 DayAlarm; /* Index to day-of-month alarm in RTC CMOS RAM */ |
294 | UINT8 MonthAlarm; /* Index to month-of-year alarm in RTC CMOS RAM */ |
295 | UINT8 Century; /* Index to century in RTC CMOS RAM */ |
296 | UINT16 BootFlags; /* IA-PC Boot Architecture Flags (see below for individual flags) */ |
297 | UINT8 Reserved; /* Reserved, must be zero */ |
298 | UINT32 Flags; /* Miscellaneous flag bits (see below for individual flags) */ |
299 | ACPI_GENERIC_ADDRESS ResetRegister; /* 64-bit address of the Reset register */ |
300 | UINT8 ResetValue; /* Value to write to the ResetRegister port to reset the system */ |
301 | UINT16 ArmBootFlags; /* ARM-Specific Boot Flags (see below for individual flags) (ACPI 5.1) */ |
302 | UINT8 MinorRevision; /* FADT Minor Revision (ACPI 5.1) */ |
303 | UINT64 XFacs; /* 64-bit physical address of FACS */ |
304 | UINT64 XDsdt; /* 64-bit physical address of DSDT */ |
305 | ACPI_GENERIC_ADDRESS XPm1aEventBlock; /* 64-bit Extended Power Mgt 1a Event Reg Blk address */ |
306 | ACPI_GENERIC_ADDRESS XPm1bEventBlock; /* 64-bit Extended Power Mgt 1b Event Reg Blk address */ |
307 | ACPI_GENERIC_ADDRESS XPm1aControlBlock; /* 64-bit Extended Power Mgt 1a Control Reg Blk address */ |
308 | ACPI_GENERIC_ADDRESS XPm1bControlBlock; /* 64-bit Extended Power Mgt 1b Control Reg Blk address */ |
309 | ACPI_GENERIC_ADDRESS XPm2ControlBlock; /* 64-bit Extended Power Mgt 2 Control Reg Blk address */ |
310 | ACPI_GENERIC_ADDRESS XPmTimerBlock; /* 64-bit Extended Power Mgt Timer Ctrl Reg Blk address */ |
311 | ACPI_GENERIC_ADDRESS XGpe0Block; /* 64-bit Extended General Purpose Event 0 Reg Blk address */ |
312 | ACPI_GENERIC_ADDRESS XGpe1Block; /* 64-bit Extended General Purpose Event 1 Reg Blk address */ |
313 | ACPI_GENERIC_ADDRESS SleepControl; /* 64-bit Sleep Control register (ACPI 5.0) */ |
314 | ACPI_GENERIC_ADDRESS SleepStatus; /* 64-bit Sleep Status register (ACPI 5.0) */ |
315 | UINT64 HypervisorId; /* Hypervisor Vendor ID (ACPI 6.0) */ |
316 | |
317 | } ACPI_TABLE_FADT; |
318 | |
319 | |
320 | /* Masks for FADT IA-PC Boot Architecture Flags (boot_flags) [Vx]=Introduced in this FADT revision */ |
321 | |
322 | #define ACPI_FADT_LEGACY_DEVICES (1) /* 00: [V2] System has LPC or ISA bus devices */ |
323 | #define ACPI_FADT_8042 (1<<1) /* 01: [V3] System has an 8042 controller on port 60/64 */ |
324 | #define ACPI_FADT_NO_VGA (1<<2) /* 02: [V4] It is not safe to probe for VGA hardware */ |
325 | #define ACPI_FADT_NO_MSI (1<<3) /* 03: [V4] Message Signaled Interrupts (MSI) must not be enabled */ |
326 | #define ACPI_FADT_NO_ASPM (1<<4) /* 04: [V4] PCIe ASPM control must not be enabled */ |
327 | #define ACPI_FADT_NO_CMOS_RTC (1<<5) /* 05: [V5] No CMOS real-time clock present */ |
328 | |
329 | /* Masks for FADT ARM Boot Architecture Flags (arm_boot_flags) ACPI 5.1 */ |
330 | |
331 | #define ACPI_FADT_PSCI_COMPLIANT (1) /* 00: [V5+] PSCI 0.2+ is implemented */ |
332 | #define ACPI_FADT_PSCI_USE_HVC (1<<1) /* 01: [V5+] HVC must be used instead of SMC as the PSCI conduit */ |
333 | |
334 | /* Masks for FADT flags */ |
335 | |
336 | #define ACPI_FADT_WBINVD (1) /* 00: [V1] The WBINVD instruction works properly */ |
337 | #define ACPI_FADT_WBINVD_FLUSH (1<<1) /* 01: [V1] WBINVD flushes but does not invalidate caches */ |
338 | #define ACPI_FADT_C1_SUPPORTED (1<<2) /* 02: [V1] All processors support C1 state */ |
339 | #define ACPI_FADT_C2_MP_SUPPORTED (1<<3) /* 03: [V1] C2 state works on MP system */ |
340 | #define ACPI_FADT_POWER_BUTTON (1<<4) /* 04: [V1] Power button is handled as a control method device */ |
341 | #define ACPI_FADT_SLEEP_BUTTON (1<<5) /* 05: [V1] Sleep button is handled as a control method device */ |
342 | #define ACPI_FADT_FIXED_RTC (1<<6) /* 06: [V1] RTC wakeup status is not in fixed register space */ |
343 | #define ACPI_FADT_S4_RTC_WAKE (1<<7) /* 07: [V1] RTC alarm can wake system from S4 */ |
344 | #define ACPI_FADT_32BIT_TIMER (1<<8) /* 08: [V1] ACPI timer width is 32-bit (0=24-bit) */ |
345 | #define ACPI_FADT_DOCKING_SUPPORTED (1<<9) /* 09: [V1] Docking supported */ |
346 | #define ACPI_FADT_RESET_REGISTER (1<<10) /* 10: [V2] System reset via the FADT RESET_REG supported */ |
347 | #define ACPI_FADT_SEALED_CASE (1<<11) /* 11: [V3] No internal expansion capabilities and case is sealed */ |
348 | #define ACPI_FADT_HEADLESS (1<<12) /* 12: [V3] No local video capabilities or local input devices */ |
349 | #define ACPI_FADT_SLEEP_TYPE (1<<13) /* 13: [V3] Must execute native instruction after writing SLP_TYPx register */ |
350 | #define ACPI_FADT_PCI_EXPRESS_WAKE (1<<14) /* 14: [V4] System supports PCIEXP_WAKE (STS/EN) bits (ACPI 3.0) */ |
351 | #define ACPI_FADT_PLATFORM_CLOCK (1<<15) /* 15: [V4] OSPM should use platform-provided timer (ACPI 3.0) */ |
352 | #define ACPI_FADT_S4_RTC_VALID (1<<16) /* 16: [V4] Contents of RTC_STS valid after S4 wake (ACPI 3.0) */ |
353 | #define ACPI_FADT_REMOTE_POWER_ON (1<<17) /* 17: [V4] System is compatible with remote power on (ACPI 3.0) */ |
354 | #define ACPI_FADT_APIC_CLUSTER (1<<18) /* 18: [V4] All local APICs must use cluster model (ACPI 3.0) */ |
355 | #define ACPI_FADT_APIC_PHYSICAL (1<<19) /* 19: [V4] All local xAPICs must use physical dest mode (ACPI 3.0) */ |
356 | #define ACPI_FADT_HW_REDUCED (1<<20) /* 20: [V5] ACPI hardware is not implemented (ACPI 5.0) */ |
357 | #define ACPI_FADT_LOW_POWER_S0 (1<<21) /* 21: [V5] S0 power savings are equal or better than S3 (ACPI 5.0) */ |
358 | |
359 | |
360 | /* Values for PreferredProfile (Preferred Power Management Profiles) */ |
361 | |
362 | enum AcpiPreferredPmProfiles |
363 | { |
364 | PM_UNSPECIFIED = 0, |
365 | PM_DESKTOP = 1, |
366 | PM_MOBILE = 2, |
367 | PM_WORKSTATION = 3, |
368 | PM_ENTERPRISE_SERVER = 4, |
369 | PM_SOHO_SERVER = 5, |
370 | PM_APPLIANCE_PC = 6, |
371 | PM_PERFORMANCE_SERVER = 7, |
372 | PM_TABLET = 8 |
373 | }; |
374 | |
375 | /* Values for SleepStatus and SleepControl registers (V5+ FADT) */ |
376 | |
377 | #define ACPI_X_WAKE_STATUS 0x80 |
378 | #define ACPI_X_SLEEP_TYPE_MASK 0x1C |
379 | #define ACPI_X_SLEEP_TYPE_POSITION 0x02 |
380 | #define ACPI_X_SLEEP_ENABLE 0x20 |
381 | |
382 | |
383 | /* Reset to default packing */ |
384 | |
385 | #pragma pack() |
386 | |
387 | |
388 | /* |
389 | * Internal table-related structures |
390 | */ |
391 | typedef union acpi_name_union |
392 | { |
393 | UINT32 Integer; |
394 | char Ascii[4]; |
395 | |
396 | } ACPI_NAME_UNION; |
397 | |
398 | |
399 | /* Internal ACPI Table Descriptor. One per ACPI table. */ |
400 | |
401 | typedef struct acpi_table_desc |
402 | { |
403 | ACPI_PHYSICAL_ADDRESS Address; |
404 | ACPI_TABLE_HEADER *Pointer; |
405 | UINT32 Length; /* Length fixed at 32 bits (fixed in table header) */ |
406 | ACPI_NAME_UNION Signature; |
407 | ACPI_OWNER_ID OwnerId; |
408 | UINT8 Flags; |
409 | UINT16 ValidationCount; |
410 | |
411 | } ACPI_TABLE_DESC; |
412 | |
413 | /* |
414 | * Maximum value of the ValidationCount field in ACPI_TABLE_DESC. |
415 | * When reached, ValidationCount cannot be changed any more and the table will |
416 | * be permanently regarded as validated. |
417 | * |
418 | * This is to prevent situations in which unbalanced table get/put operations |
419 | * may cause premature table unmapping in the OS to happen. |
420 | * |
421 | * The maximum validation count can be defined to any value, but should be |
422 | * greater than the maximum number of OS early stage mapping slots to avoid |
423 | * leaking early stage table mappings to the late stage. |
424 | */ |
425 | #define ACPI_MAX_TABLE_VALIDATIONS ACPI_UINT16_MAX |
426 | |
427 | /* Masks for Flags field above */ |
428 | |
429 | #define ACPI_TABLE_ORIGIN_EXTERNAL_VIRTUAL (0) /* Virtual address, external maintained */ |
430 | #define ACPI_TABLE_ORIGIN_INTERNAL_PHYSICAL (1) /* Physical address, internally mapped */ |
431 | #define ACPI_TABLE_ORIGIN_INTERNAL_VIRTUAL (2) /* Virtual address, internallly allocated */ |
432 | #define ACPI_TABLE_ORIGIN_MASK (3) |
433 | #define ACPI_TABLE_IS_VERIFIED (4) |
434 | #define ACPI_TABLE_IS_LOADED (8) |
435 | |
436 | |
437 | /* |
438 | * Get the remaining ACPI tables |
439 | */ |
440 | #include "actbl1.h" |
441 | #include "actbl2.h" |
442 | #include "actbl3.h" |
443 | |
444 | /* Macros used to generate offsets to specific table fields */ |
445 | |
446 | #define ACPI_FADT_OFFSET(f) (UINT16) ACPI_OFFSET (ACPI_TABLE_FADT, f) |
447 | |
448 | /* |
449 | * Sizes of the various flavors of FADT. We need to look closely |
450 | * at the FADT length because the version number essentially tells |
451 | * us nothing because of many BIOS bugs where the version does not |
452 | * match the expected length. In other words, the length of the |
453 | * FADT is the bottom line as to what the version really is. |
454 | * |
455 | * For reference, the values below are as follows: |
456 | * FADT V1 size: 0x074 |
457 | * FADT V2 size: 0x084 |
458 | * FADT V3 size: 0x0F4 |
459 | * FADT V4 size: 0x0F4 |
460 | * FADT V5 size: 0x10C |
461 | * FADT V6 size: 0x114 |
462 | */ |
463 | #define ACPI_FADT_V1_SIZE (UINT32) (ACPI_FADT_OFFSET (Flags) + 4) |
464 | #define ACPI_FADT_V2_SIZE (UINT32) (ACPI_FADT_OFFSET (MinorRevision) + 1) |
465 | #define ACPI_FADT_V3_SIZE (UINT32) (ACPI_FADT_OFFSET (SleepControl)) |
466 | #define ACPI_FADT_V5_SIZE (UINT32) (ACPI_FADT_OFFSET (HypervisorId)) |
467 | #define ACPI_FADT_V6_SIZE (UINT32) (sizeof (ACPI_TABLE_FADT)) |
468 | |
469 | #define ACPI_FADT_CONFORMANCE "ACPI 6.1 (FADT version 6)" |
470 | |
471 | #endif /* __ACTBL_H__ */ |
472 | |